q9450+asus maximus extreme

[ankonex]

salz,
Q9450(thermalight ifx-14), asus maximus extreme (bios 1102), corsair 2x2giga 1600mhz (CM3X2g1600c9DHX).

Daca mai are careva q9450 sau asus maximus extreme si imi poate da niste indicatii plz

Setarile din bios ale mele sunt urmatoarele:

-Ai overclock tune = manual
-OC mem lev up= auto
-cpu ratio set= 8.0
-FSB frecv= 333
-pci frecv= 100

-ddram frecv = ddr1333mhz
-ddram command rate = 2t
-ddram timing control= manual
-cash# latency = 9
-ras# to cas# latency =9
-ras# precharge = 9
-ras# active time=24
-ras# to ras# delay = auto
-row refresh cycle time = auto
-write ricovery time = auto
-read to precharge time = auto
-read to write delay (s/d)= auto
-write to read delay (s)= auto
-write to read delay (d)= auto
-read to read delay (s)= auto
-read to read delay(d)= auto
-write to write delay (s)= auto
-write to write delay (d)= auto
-ddram static read control = disable
-dram dynamic write control= disable
-Ai clock twister = strong
-ai clock skew for chanel A = auto
-ai clock skew for chanel B = auto
-Ai transaction booster = enable
-Boost level=2

-Cpu voltage 1.24375v (temperatures at full load 68*c with core temp 0.99)
-cpu ppl voltage = 1.50v
-north bridge voltage= 1.25v
-ddram voltage = 1.80v
-Fsb termination voltage= 1.20v
-south bridge = 1.050v
-Loadline calibration = enable
-Cpu gtl reference= x63
-north bridge gtl reference = x67
-ddr3 chanel A+B REF voltage = auto
-ddr3 controller REF voltage = ddr3_REF
-sb 1.5 voltage = auto

CPU ADVANCED SETTINGS
-Cpu ratio setting = [8.0]
-C1E support = disable
-Cpu tm function = disable
-vanderpool technology = disable
-execute disable BIT = disable
-MAC CPUID value limit = disable

North Bridge chipset conf.
-memory remap value feature=enable
-initiate graphic adapter= [PEG/PCO]
-PEG Port control = auto
-peg port force x1 = disable

PCIPnp
-plug and play O/S = [NO]

POWER
-suspend mode = [auto] (u can set to S1 (po)only or S3 only)
-repost video on S3 resume = disable
-ACPI 2.0 support = enable
-ACPI APIC support = enable

SATA conf.
-sata config = [enchanted] (u can set ro disable or compatible)
-configure sata os = IDE (raid or AHCI)
-Hard disk write protect disable
-sata detect time out (sec) = [0]


nu pot sa il fac stabil la 400fsb sau la 450fsb , imi da ecrane albastre dupa 1-ore

buteaza cu voltajele default si la 400 si la 450 numai ca la 450 nu mi se incarca anumite programe ca nvidia video driver , bitdefender etc

si la 400 imi da ecrane albastre dupa un anumit timp

am skimbat voltajele , latentele la ram , am dar ramul in jos cu o treapta (de la 1333mhz la 1066mhz) nu il pot stabiliza nici la 400(am mai incercat 401,410 fsb)

am incercat alte voltaje
-Cpu voltage 1.24375v ( cu default mia dat ecran albastru dupa o ora la fsb 400 temp@71*c si cu 1.35v cpu freeezz dota 15 min , temperatura a urcat 77*c)
-cpu ppl voltage = 1.60v
-north bridge voltage= 1.40v
-ddram voltage = 1.84v (1.90 . 2.0. 2.4v)
-Fsb termination voltage= 1.40v
-south bridge = 1.100v

temperaturile sunt masurate cu COre temp 0.99 , in real temp 2.60 sunt cu 10 grade mai mici ; aceste temp sunt temperaturile corurilor

temperatula la cpu este cea din bios si este intre 17-30*c full load